|
 
SUNGARD is used to preserve, protect and
beautify smooth asphalt roofs, modified bitumen roofs and granule
finished roofs. It is not a waterproofing coating.
SUNGARD is used to protect metal structure and is a anti-rust and
corrosion coating.
SUNGARD is used on asphalt roofs, metal roofs, metal walls, masonry
walls etc. to reflect sun rays in order to reduce air-conditioning costs
in summer and heating costs in winter.
BITUMAT
SUNGARD is easy to apply, requiring no heating or thinning.
Highly reflective, reflecting up to 70% of the harmful sun rays, thus
prolonging the life of bitumen roofs.
Reduces surface temperature by as much as 10 °C; thus reducing cooling
and heating costs. Cuts maintenance cost on roofs and walls. Pliable and
flexible, capable of withstanding thermal and structural movement in
roofs and walls.
Economical. High coverage rates, one kg covers upto 6M2.
Easy to apply - saves labour costs.
Thoroughly clean the surface to be coated. All dirt,
dust, scale, loose coating and rust must be removed and the surface must
be dry before coating. On old metal or galvanized steel, remove rust and
scale by wire brush. Over new galvanized steel, pre-treat the surface
with diluted muratic acid (5%).
|
Clean with kerosene
Hands : Use a hand cleaner or kerosene followed by soap and water.
Around 0.15 Kg/M2 on metal, wood or
smooth bituminous surfaces.
Around 0.27 Kg/MZ on granule, rough or concrete surfaces.
Complies with ASTM D2824, Type I.
20-Kg pails and 200-Kg drums.
Contains petroleum distillate; flammable; keep away from
open fire, sparks or other ignition sources. Wear protective clothing,
gloves and goggles.
 Fire - Flammable when
wet, flash point 40 °C.
Skin
- Avoid repeated or prolonged contact; if contact occurs remove with
hand cleaner that removes oil or grease; then clean with soap and water.
Eyes-Avoid
contact, causes irritation; if contact occurs flush with clean water.
Inhalation
- Can cause dizziness. Remove to fresh air and if breathing difficulty
persist, administer oxygen
|
 |
 |
 |
| Density at 250C.,
Kg/Lt |
0.99 - 1.03 |
ASTM D- 70 |
| Viscosity at 250. cps |
300- 600 |
Brookfield |
| Colour, cured |
Bright silver |
- |
| Colour, wet |
Brown |
- |
| Drying time, to touch, Hr. |
2 |
- |
| Drying time, Hr. |
24 |
- |
| Adhesion to dry surfaces |
Excellent |
- |
| Reflectance % |
70 (min) |
ASTM D-2824 |
| Resistance to heat at 60 0C |
No sagging or blistering |
ASTM D-2822 |
Resistance
to water under drainage,
under standing water |
Good Poorr |
- |
| Service temperature.0C |
-5 to 60 |
- |
| Non volatile, % Wt |
50-60 |
ASTM D-2824 |
| Volatile, % Wt |
40 to 48 |
ASTM D-2824 |
| Metallic Aluminium content, % Wt. |
22 (min) |
ASTM D-2824 |
Pigments, stabilizers and additives,
% Wt |
18 |
ASTM D-2824 |
| Resistance to
solvents |
Poor |
- |
The information given in this Technical Sheet is to the best of our knowledge based on
laboratory tests and practical experience. However, as the product is often used under conditions beyond our control, we cannot guarantee but the product itself.
|
